top of page

CERTIFICATION

GL - ANSI_Z97_1-2004 - Boil Test_.jpg

BOIL TEST

ANSI Z97.1-2004

- US Standards

GL - BS_EN_356_2000 - Anti-Intrusion Tes

ANTI-BURGLARY TEST

BS EN 356:2000

- European Standards

GL - ASTM_G154_16_Cycle_1_ISO_105_A02_19

LIGHT AGEING TEST-UV EXPOSURE

ASTM G154-16 Cycle 1& ISO 105-A02:1993 / Cor:2:2005

- ASTM / ISO Standards

GL - SS341_2001(2012)_Page_1.jpg

BOIL TEST

SS341:2001(2012)

- Singapore Standards

GL - SS341_2001(2012)_Page_1.jpg

WARPAGE TEST

SS341:2001(2012)

- Singapore Standards

GL - ANSI_Z97_1-2004 - Impact Test_.jpg

IMPACT TEST

ANSI Z97.1-2004

- US Standards

GL - BS_476_PART_7_1997 - Fire Test_.jpg

FIRE TEST

BS 476 Part 7 1997

- British Standards

GL - BS_6206_1981 - Impact Test_.jpg

IMPACT TEST

BS 6206:1981

- British Standards

GL - ISO_2409_2013 - Adnesion Test - Cro

ADHESION TEST / CROSS-CUT TEST

ISO 2409:2013

- International Standards

GL - SS341_2001(2012)_Page_1.jpg

IMPACT TEST

SS341:2001(2012)

- Singapore Standards

GL - ASTM_D4752-10-2015 - Solvent_Resist

SOLVENT RESISTANCE RUB TEST

ASTM D4752-10 (2015)

- ASTM Standards

​DOWNLOADs

Boil Test | ANSI Z97.1-2004

ANSI Z97.1-2004

BOIL TEST

for Fabric Mesh Laminated Glass

Certification:

ANSI Z97.1 Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of Test - Clause 5.3.2 – ( 1 ) Boil Test

Standard:

ANSI Z97.1-2004 Standard was developed under procedures accredited as meeting the criteria for American National Standards

Tested Material:

Fabric Mesh Laminated Glass

Process:

Determining the effect of exposure of safety glazing materials to temperature and humidity condition by boiling.

  1. Immerse the specimens vertically on edge in a bath of water maintained at a temperature of 66°C ± 3°C for 3 min

  2. Quickly transfer the specimens to a bath of water maintain at boiling point. Immerse the specimens vertically on edge for 2 h

  3. Remove the specimens and examine for the bubbles and others defects

Result:

The purpose of weathering [LG or OCG] is to determine if degradation of the interlayer occurs over the duration of the exposure. No bubbles or delaminations shall develop more than 0.5 in. from the outer edge of the specimen or any crack.

Application:

Kitchen Cabinet Glass, Shower Glass Partition, Door Glass.

Keywords:

Heat-resistant glass, Safety Glass.

BOIL TEST

SS341:2001(2012)

for Art Laminated Tempered Glass

Certification:

SS341:2001(2012) Specification for Impact Performance Requirements for the Flat Safety Glass and Safety Plastics for use in Buildings

Standard:

SS341:2001(2012) Standard was developed under procedures accredited as meeting the criteria for Singapore Standards Institution

Tested Material:

Art Laminated Tempered Glass

Process:

Determining the effect of exposure of safety glazing materials to temperature and humidity condition by boiling.

  1. Time of glass immersion in water at 65.0 °C for 3 mins

  2. Time of glass immersion in water at 100.0 °C for 120 mins

  3. Remove the specimens and examine for the bubbles and others defects

Result:

Pass

Application:

Windows, Partition, Wall glass panel.

Keywords:

Toughen glass, Safety Glass, Strengthen Glass, Stratobel Security Burglary

Boil Test | SS341:2001(2012)
Impact Test | ANSI Z97.1-2004

IMPACT TEST

ANSI Z97.1-2004

for Fabric Mesh Laminated Glass

Certification:

ANSI Z97.1 Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of Test - Impact Test

Standard:

ANSI Z97.1-2004 Standard was developed under procedures accredited as meeting the criteria for American National Standards

Tested Material:

Fabric Mesh Laminated Glass

Process:

testing method comprises both hammer and axe (weight 2kg) strikes on the 400 mm x 400 mm square area of a vertically positioned glass with the size 1,100 x 900 mm. At least 12 hammer strikes are used to destroy the testing glass first and then the following axe cutting strikes are tried to make an opening. The axe test is passed if the square opening (400 mm x 400 mm) is not formed and completely detached from the rest of the test sheet. Finally the number of strikes are counted and classified as P6B to P8B which denote their resistant ability to penetrate the glass.

Result:

Type 1 = no tear or shear or opening develops within the vertical specimen through with a 3.0 in diameter sphere can pass;

Type 2 = "the 10 largest crack-free particles shall be selected and weighed… the average thickness will be used to determine the maximum allowable weight";

Type 3 = "the stiffness and hardness of the specimen shall be determined"; for

Type 4 = No breakage occurs.

The interpretation of results for center punch fragmentation is "the total of the 10 largest crack-free pieces shall weigh no more than the equivalent weight of 10 square inches of the original test sample.

Application:

Kitchen Cabinet Glass, Shower Glass Partition, Door Glass.

Keywords:

Toughen glass, Safety Glass, Strengthen Glass, Stratobel Security Burglary.

IMPACT TEST

BS 6206:1981

for Fabric Mesh Laminated Tempered Glass

Certification:

BS 6206:1981 Specification for Impact Performance Requirements for the Flat Safety Glass and Safety Plastics for use in Buildings

Standard:

BS 6206:1981 Standard was developed under procedures accredited as meeting the criteria for British Standards Institution

Tested Material:

Fabric Mesh Laminated Tempered Glass

Process:

  1. Immediately preceding the test, condition the test piece as described above. Place the test piece in the frame and clamp it so that the chloroprene strips are compressed by no more than 10% to 15% of their original thickness. When the impactor is hanging at rest, suspended from the overhead support, check that it is, at its greatest diameter, not more than 13mm from the surface of the test piece and within 51mm radially from the centre of the test piece.

  2. Raise the impactor to a drop height of 305mm and steady it.

  3. Release the impactor so that it swings in a pendulum arc and strikes the piece.

  4. Inspect the test piece after impact and report whether: 

    • It has remained unbroken. 

    • It has broken safely in accordance with the requirements of 6.2. 

    • It has broken and failed to comply with the requirements of 6.2.

  5. If any test piece fails to comply with the requirements of 6.2, terminate the procedure. If all four test pieces either do not break or break safely and if it is required to test the material to a higher impact level, increase the drop height to 457mm and repeat the test on four more test pieces of the same material or test pieces which have undergone the previous tests and remained unbroken.

  6. Repeat the same procedure for drop height of 1219mm.

Result:

Class A: Complied

Class B: Complied

Class C: Complied

Application:

--------​

Keywords:

Toughen glass, Safety Glass, Strengthen Glass, Stratobel Security Burglary

Impact Test | BS 6206:1981

IMPACT TEST

SS341:2001(2012)

for Art Laminated Tempered Glass

Certification:

SS341:2001(2012) Specification for Impact Performance Requirements for the Flat Safety Glass and Safety Plastics for use in Buildings

Standard:

SS341:2001(2012) Standard was developed under procedures accredited as meeting the criteria for Singapore Standards Institution

Tested Material:

Art Laminated Tempered Glass

Process:

  1. Testing involves dropping laminated glass from different height.

    • 300mm

    • 450mm

    • 600mm

    • 750mm

    • 900mm

    • 1200mm

    • 1500mm

  2. The purpose is to evaluate the durability of the glass.

  3. The test assesses the glass's ability to withstand impact

  4. Results can inform product design and manufacturing processes

Result:

2) It has broken and numerous cracks or fissures appear but no shear or opening develops within the body of the glazing material through which a 76 mm diameter sphere can be passed freely; additionally, if fragments are detached from the test piece up to 3 min after impact, they shall, in total, weigh no more than the mass equivalent to 10 000 mm² of the original test piece and the largest single fragment shall weigh less than the mass equivalent to 4400 mm² of the original test piece.

Application:

--------​

Keywords:

Toughen glass, Safety Glass, Strengthen Glass, Stratobel Security Burglary

Impact Test | SS341:2001(2012)
Anti-Burglary Test | BS EN 356:2000

ANTI-BURGLARY TEST

BS EN 356:2000